spice

Files (13)

• SKILL.md
• simulation-models.md · references/
• extract_parasitics.py · scripts/
• simulate_subcircuits.py · scripts/
• spice_model_cache.py · scripts/
• spice_model_generator.py · scripts/
• spice_models.py · scripts/
• spice_part_library.py · scripts/
• spice_results.py · scripts/
• spice_simulator.py · scripts/
• spice_spec_fetcher.py · scripts/
• spice_templates.py · scripts/
• spice_tolerance.py · scripts/

SKILL.md (first lines)

# SPICE Simulation Skill

Automatically generates and runs SPICE testbenches for circuit subcircuits detected by the `kicad` skill's schematic analyzer. Supports ngspice, LTspice, and Xyce (auto-detected). Validates calculated values (filter frequencies, divider ratios, opamp gains) against actual simulation results and produces a structured report.

This skill inverts the typical simulation workflow: instead of requiring users to create simulation sources and configure analysis (which ~2.5% of KiCad users do), it generates targeted testbenches automatically from the analyzer's subcircuit detections.

## Related Skills

| Skill | Purpose |
|-------|---------|
| `kicad` | Schematic/PCB analysis — produces the analyzer JSON this skill consumes |
| `digikey` | Parametric specs for behavioral models, datasheet downloads |
| `mouser` | Parametric specs (secondary source), datasheet downloads |
| `lcsc` | Parametric specs (no auth needed), datasheet downloads |
| `element14` | Parametric specs (international), datasheet downloads |
| `emc` | EMC pre-compliance — uses this skill's simulator infrastructure for SPICE-enhanced PDN impedance and EMI filter analysis |

**Handoff guidance:** The `kicad` skill's `analyze_schematic.py` produces the analysis JSON with subcircuit detections in the flat `findings[]` array (filtered by `detector` field). This skill reads that JSON, generates SPICE testbenches for simulatable subcircuits, runs the detected simulator (ngspice/LTspice/Xyce), and produces a structured verification report. Always run the schematic analyzer first. During a design review, run simulation after the analyzer and before writing the final report — simulation results should appear as a verification section in the report. The `emc` skill reuses this skill's simulator backend for SPICE-enhanced PDN impedance and EMI filter insertion loss checks — when ngspice is available, the EMC skill's `--spice-enhanced` flag activates these checks automatically.

## Requirements

- **A SPICE simulator** — one of the following (auto-detected, first available wins):
  - **ngspice** — `sudo apt install ngspice` (Linux) / `brew install ngspice` (macOS) / ngspice.sourceforge.io (Windows). Most common choice.
  - **LTspice** — free from analog.com/ltspice. Popular on Windows, works via wine on Linux.
  - **Xyce** — from xyce.sandia.gov. Parallel SPICE for large circuits.
  - Override with `--simulator ngspice|ltspice|xyce` or `SPICE_SIMULATOR` env var.
- **Python 3.10+** — stdlib only, no pip dependencies
- **Schematic analyzer JSON** — from `analyze_schematic.py --output`

If no simulator is installed, skip simulation gracefully and note it in the report. Do not treat a missing simulator as an error — it's an optional enhancement.

## Workflow

### Step 1: Run the schematic analyzer

```bash
python3 <kicad-skill-path>/scripts/analyze_schematic.py design.kicad_sch --analysis-dir analysis/
```

### Step 2: Run SPICE simulations

Pass `--analysis-dir analysis/` — the script auto-resolves `schematic.json`
from the manifest's current run, writes `spice.json` into the same run
folder, and parks intermediate `.cir` / `.raw` files at
`<run>/spice_work/` by default.

```bash
# Recommended: auto-resolve schematic + write spice.json into the current run
python3 <skill-path>/scripts/simulate_subcircuits.py --analysis-dir analysis/

# Explicit form — positional or --schematic path
python3 <skill-path>/scripts/simulate_subcircuits.py analysis.json --output sim_report.json

# Simulate specific types only
python3 <skill-path>/scripts/simulate_subcircuits.py --analysis-dir analysis/ --types rc_filters,voltage_dividers

# Keep simulation files for debugging (default: <run>/spice_work/ when --analysis-dir is set, else a temp dir)
python3 <skill-path>/scripts/simulate_subcircuits.py --analysis-dir analysis/ --workdir ./spice_runs

# Increase timeout for complex circuits (default: 5s per subcircuit)
python3 <skill-path>/scripts/simulate_subcircuits.py --analysis-dir analysis/ --timeout 10

# Omit file paths from output (cleaner for reports)
python3 <skill-path>/scripts/simulate_subcircuits.py --analysis-dir analysis/ --compact
```

### Step 2b (optional): PCB parasitic-aware simulation

When both schematic and PCB exist, run parasitic-annotated simulation for more accurate results on analog circuits:

```bash
# Analyze PCB with full trace segment detail
python3 <kicad-skill-path>/scripts/analyze_pcb.py design.kicad_pcb --full --output pcb.json

# Extract parasitic R/L/C from PCB geometry
python3 <skill-path>/scripts/extract_parasitics.py pcb.json --output parasitics.json

# Run simulation with PCB parasitics injected into testbenches
python3 <skill-path>/scripts/simulate_subcircuits.py analysis.json --parasitics parasitics.json --output sim_report.json
```

With `--parasitics`, testbenches include trace resistance and via inductance between components. The report shows the parasitic impact — e.g., "48mΩ trace resistance shifts RC filter fc down 0.3%."

**When to use parasitic simulation:** Consider it when the design has high-impedance feedback networks (>100kΩ), LC filters or RF matching networks, long analog signal traces, or high-frequency circuits where trace inductance matters. For typical digital designs with low-impedance power regulation, the ideal simulation is sufficient.

### Step 2c (optional): Monte Carlo tolerance analysis

Run N simulations per subcircuit with randomized component values within tolerance bands. Reports statistical distributions and sensitivity analysis — which component contributes most to output variation.

```bash
# Run 100 Monte Carlo trials per subcircuit
python3 <skill-path>/scripts/simulate_subcircuits.py analysis.json --monte-carlo 100 --output sim_report.json

# Use uniform distribution (conservative worst-case envelope) instead of Gaussian
python3 <skill-path>/scripts/simulate_subcircuits.py analysis.json --monte-carlo 100 --mc-distribution uniform

# Set random seed for reproducibility (default: 42)
python3 <skill-path>/scripts/simulate_subcircuits.py analysis.json --monte-carlo 100 --mc-seed 123
```

**Tolerance sourcing:** Tolerances are extracted from component value strings first (e.g., "680K 1%" → 1%, "22uF/6.3V/20%/X5R" → 20%). When not specified in the value string, defaults are used: resistors 5%, capacitors 10%, inductors 20%.

**Output:** Each simulation result gains a `tolerance_analysis` section with:
- **statistics**: mean, std, min, max, 3-sigma bounds, spread percentage for the primary output metric (fc, Vout, gain, etc.)
- **sensitivity**: per-component contribution percentage showing which component dominates variation (e.g., "C3 (10% tol) contributes 68% of fc variation, R5 (5% tol) contributes 32%")
- **components**: list of toleranceable components with their resolved tolerance values

**When to use Monte Carlo:** Use it for feedback networks (regulator output accuracy), precision voltage dividers, RC/LC filters near spec limits, and any circuit where tolerance stacking could push behavior outside acceptable bounds. For N=100 at ~5-50ms per simulation, expect ~0.5-5s per subcircuit.

### Step 3: Interpret results and present to user

Read the JSON report and incorporate findings into the design review. See the "Interpreting Results" and "Presenting to Users" sections below.

## What Gets Simulated

The script selects subcircuits from the analyzer's `findings[]` array (grouped by detector type). Not every detection is simulatable — the script skips configurations that can't produce meaningful results (comparators, open-loop opamps, active oscillators).

| Detector | Analysis | What's Measured | Model Fidelity | Trustworthiness |
|----------|----------|-----------------|----------------|-----------------|

From aklofas/kicad-happy, MIT.

More from aklofas/kicad-happy